Dr Fixit Roofseal Topcoat Waterproofing Solution Expert

Product details
Packaging Size:
Brand:	Dr Fixit
Usage surfaces:	Roof, Terrace

Dr Fixit Roofseal Topcoat

Step 1: Surface Preparation Preparing the surface thoroughly by cleaning, washing and removing dust, dirt, oil, grease and lose particles. Existing roof systems will be visually inspected for conditions that may adversely affect the adhesion of performance of newly installed products. Damaged or hollow portions, sharp edges, etc. will be cut and repaired with a polymer-modified mortar using Dr. Fixit Pidicrete URP. Check if roof slope of a minimum of 1 in 100 is already provided. Step 2: Crack Filling Cracks up to 1 mm with Dr. Fixit Roofseal Top Coat directly by brush or roller after cleaning the cracks. All surface cracks up to 5 mm width will be filled up with Dr. Fixit Crack-X paste. In existing old terraces with brickbat coba or screeds, the substrate must be checked for its soundness, damaged or hollow portions, sharp edges, any weak surface layer etc will be removed up to slab level. Just before laying the Polymer modified mortar screed, reinstate the surface with bond coat slurry mix with Dr. Fixit Pidicrete URP in the ratio of 1:1 (1 part URP : 1 part Cement). Level the surface with Polymer modified mortar mixing with Dr. Fixit Pidicrete URP 10 to 15% by weight of cement in the CM ratio of 1:3. Step 3: Coating Application All joints/corners/drainage outlets and penetration points will be treated prior to all application of Dr. Fixit Roofseal Top Coat. All corners, gaps, joints, protrusions and outlets will be coated with an extra coat incorporating reinforcing fabric. Dr. Fixit Roofseal Top Coat may be applied by roller or brush. Application of a coat of Dr. Fixit Roofseal Top Coat (diluted with water in the ratio 2:1) as Self Priming - 9 - 10 Sq.mtr / litre. Allow coating to dry for 3-4 hours prior to applying first coat & second coat. Applying two coats of Dr. Fixit Roofseal Top Coat @ 2 - 2.2 Sq.mtr / litre/coat, without water dilution, the rate of the application being the same for both the coats. This would ensure the correct consumption of material that will deliver a total DFT of 450– 500 micron. System to air cure for 3 days minimum.

Disclaimer: The products listed are solely for information. We neither sell nor endorse any products listed on the website. All the information on this page is for general information purposes only.

Waterproofing FAQs

Q. How do I calculate waterproofing cost for Dr Fixit Roofseal Topcoat? We've developed WATERPROOFING COST CALCULATOR where you can calculate the tentative cost of waterproofing.
Q. How do I apply Dr Fixit Roofseal Topcoat? Step 1: Surface Preparation Preparing the surface thoroughly by cleaning, washing and removing dust, dirt, oil, grease and lose particles. Existing roof systems will be visually inspected for conditions that may adversely affect the adhesion of performance of newly installed products. Damaged or hollow portions, sharp edges, etc. will be cut and repaired with a polymer-modified mortar using Dr. Fixit Pidicrete URP. Check if roof slope of a minimum of 1 in 100 is already provided. Step 2: Crack Filling Cracks up to 1 mm with Dr. Fixit Roofseal Top Coat directly by brush or roller after cleaning the cracks. All surface cracks up to 5 mm width will be filled up with Dr. Fixit Crack-X paste. In existing old terraces with brickbat coba or screeds, the substrate must be checked for its soundness, damaged or hollow portions, sharp edges, any weak surface layer etc will be removed up to slab level. Just before laying the Polymer modified mortar screed, reinstate the surface with bond coat slurry mix with Dr. Fixit Pidicrete URP in the ratio of 1:1 (1 part URP : 1 part Cement). Level the surface with Polymer modified mortar mixing with Dr. Fixit Pidicrete URP 10 to 15% by weight of cement in the CM ratio of 1:3. Step 3: Coating Application All joints/corners/drainage outlets and penetration points will be treated prior to all application of Dr. Fixit Roofseal Top Coat. All corners, gaps, joints, protrusions and outlets will be coated with an extra coat incorporating reinforcing fabric. Dr. Fixit Roofseal Top Coat may be applied by roller or brush. Application of a coat of Dr. Fixit Roofseal Top Coat (diluted with water in the ratio 2:1) as Self Priming - 9 - 10 Sq.mtr / litre. Allow coating to dry for 3-4 hours prior to applying first coat & second coat. Applying two coats of Dr. Fixit Roofseal Top Coat @ 2 - 2.2 Sq.mtr / litre/coat, without water dilution, the rate of the application being the same for both the coats. This would ensure the correct consumption of material that will deliver a total DFT of 450– 500 micron. System to air cure for 3 days minimum.
Q. Do you provide any service warranty for Dr Fixit Roofseal Topcoat? There are two kinds of warranties involved in painting process. 1. Paint Product Warranty and 2. Service Warranty. Paint Product warranty if applicable is directly provided by manufacturers of paint (with their TERMS & CONDITIONS ). Our painting service warranty will be of 1 year in selected painting systems.
Q. In what variants and packaging price Dr Fixit Roofseal Topcoat Is available? Dr Fixit Roofseal Topcoat Is Available in different variant listed below.
Q. Can I use Dr Fixit Roofseal Topcoat for Roof leakage waterproofing? Yes, Dr Fixit Roofseal Topcoat can be used for Roof leakage waterproofing
Q. Can I use Dr Fixit Roofseal Topcoat for Terrace leakage waterproofing? Yes, Dr Fixit Roofseal Topcoat can be used for Terrace leakage waterproofing